The Ultimate Guide on the Best Ripping Blade for Table Saw

Are you looking for blades that are designed for cutting along the grain of the workpiece? Then, you will need the ripping blades, which generally have 10-30 teeth. A good quality ripping blade can make woodworking more enjoyable for you. 

We always want a blade with top-notch performance and durability. But when we go to purchase one, we discover a sea of choices and fall confused about which one to choose.

Don’t worry! I have narrowed down 5 Best Ripping Blade For Table Saw to help you out in the crowd. 

Have a quick glance at my top recommended ripping blades for table saw you can buy in 2021:

Freud 10″ x 24T  – Heavy-Duty One For Your Tough Jobs

Freud 10″ x 30T – Industrial-Grade Ripping Blade

Forrest WW10407125  – High-End Blade With Versatile Features

DEWALT 10-Inch Miter / Table Saw Blades – Great Affordable Set

Freud D1050X Diablo 10″ – Both for Ripping and Crosscutting

What is Ripping?

Ripping refers to trimming the material along its grain for a lengthwise cut. And the rip blade is specially made for cutting through wood fibers and leaving a clean edge. 

The gullet or gap between the teeth is large for handling the large amount of material required in rip cuts and remove sawdust. There are also combination blades that have beveled teeth like crosscut blades and FT teeth like rip blades. 

5 Best Ripping Blade for Table Saw: An Honest Review

When choosing the top-rated one, we can get confused with so many options. Check out my recommended product for choosing the right one for you.

Freud 10″ x 24T  – Heavy-Duty One For Your Tough Jobs

If you want a dedicated table saw blade for ripping the hard and softwoods, Freud has designed the LM72R010 to primarily function as a rip cutter. So, the teeth are hooked and flat to deliver a smooth finish on the workpiece. 

The extra-large flat teeth will cut most types of woods down to size at a fairly quick rate. Remember, 8000 RPM is the standard and recommended maximum rate for this 10” diameter. 

These laser-cut teeth will ensure the leading edges of the blade will remain strong and sharp for a longer span. However, the blade can cut in an unstable fashion in some saws. 

This full kerf blade is 1/8” wide with bigger teeth with an anti-kickback formula, which helps to reduce the kickback. And its carbide teeth are twice as large on the smaller blades. It comes with 24 teeth with a flat grind and a 20° hook angle. 

On the whole, if you are trying to take a really thin shaving off the side of the piece of the workpiece, a thick full kerf like this one should be able to hold the line more easily rather than bending of the side.

Pros

  • Smooth cuts 
  • Doesn’t provide noise
  • Less chance to wobble
  • Low tendency to wrap 
  • Great performance and lasts long

Cons

  • Creates more sawdust 

Freud 10″ x 30T – Industrial-Grade Ripping Blade

Freud, the Italian company, has excellence in providing top-notch table saw blades. And the 10”x30T Industrial Glue Line ripping blade is not any exception. 

This cutting tool comes with the TiCo Hi-density specially formulated carbide to maximize performance. This glue line ripping blade comes with 220volt with 3HP.

This thick kerf table saw blade has less chance of bend or wrap. When you have powered saws, this full kerf blade can ensure a nice, stable cut. The Laser-cut anti-vibration slots reduce the wobbling and extend the blade life. 

However, since the blades are wider, it cuts more material and creates more sawdust. That being said, the large gullets are for cutting fibrous wood material along the grain of the wood. And these large gullets help to remove the material. 

This industrial-grade blade has 30 teeth with TCG grind and a 12° Hook angle. And you are paying for the longer-lasting blade with the ability to sharpen at more times. Glue-line rip blades require a steady feed.

It has a slightly slower feed rate than a standard rip blade, but it leaves cleaner edges that may not require jointing before gluing. This blade can also cut abrasive materials like particleboard for its durable TCG teeth, which saves your general-purpose blade for crosscutting solid wood and hardwood plywood. So, rather than buying cheaper blades, you can have one industrial blade. Its non-slip coating is better than red Perma shield coating. 

Overall, Freud gives you finished faces that are quite ready to glue. 

Pros

  • Less wobble
  • The heavy-duty thick kerf 
  • More carbides for easy cut 
  • Crisp, splinter-free flawless finish
  • More ability to sharpen more times
  • Introduce more harmonic vibration into the saw blade

Cons

  • Not for the unpowered saws

Forrest WW10407125  High-End Blade With Versatile Features

The Forest woodworker saw blade from the American manufacturers – is a top-of-the-line product with its high performance and multi-use capabilities. It might get a high price tag, but its 15° alternative bevel teeth configuration, blade performance of both rip cuts and crosscuts will suffice your requirements. Besides, you don’t have to face the hassle of changing the blades. 

Its build quality is top-notch. It will offer a glue-like, splinter-free finish. You can expect maximum precision with its hand-tensioning and C-4 carbide construction. This thick kerf can cut up to 2-inches thick timber.

Since it has a 20° face hook angle, it makes the feed rate much easier and provides a dedicated ripping-blade-like finish. The side clearance keeps it away from scratching. 

The side wobble is held to .001, and so you won’t get any flutter. The grind of the tooth is an alternative top bevel, which gives a shearing job. The carbide lasts longer than other competitions. However, it is not so good for precision dados. 

On top of that, if you need to resharpen it, you can send it to the factory with its box. 

Pros

  • Lasts longer
  • High-grade carbide
  • Performs both rip cuts and crosscuts very well
  • The side clearance is for reducing the scratching 
  • The alternative bevel teeth give nice, smooth cuts

Cons

  • Expensive 

DEWALT 10-Inch Miter / Table Saw BladesGreat Affordable Set

If you don’t want to break your bank yet are looking for a great deal, the DeWalt 10-inch blade prices at just a fraction of other blades. It is a great deal to outfit your table saw. Since this pack has two blade sets, your ripping, and crosscutting jobs will be covered. 

The thinner kerf is an excellent option for softwoods to hardwoods for producing a faster and smooth cut. This blade takes big bites of wood, and the spaces between the teeth make the woodchips exit better. 

And you can get faster, more efficient cutting with less chance of scorching the wood. However, it may exhibit kickbacks for the angle of the teeth. 

The tungsten carbide construction speaks of durability and longevity. It stays sharper for a long span. Again, the computer-balanced plate lessens the vibration for improved accuracy. It also reduces noisy operation without heating up. 

Pros

  • Quite fast
  • Affordable
  • The venting ensures quiet operation 
  • The shoulder design is for more power behind the teeth 

Cons

  • It can kick back a bit

Freud D1050X Diablo 10″ – Both for Ripping and Crosscutting

If you want ‘a jack of all trades’, Diablo 1050X is what you are looking for. The thin kerf of this combination blade is quite popular in the market. Its affordable price makes it lucrative to most buyers. 

This 50-tooth combination blade, the original hybrid design is half rip and half crosscut. It features a super-thin laser cut kerf, Perma-SHIELD nonstick coating, tri-metal shock-resistant brazing, and more.

If you look at the combination of the blades, it has 50 teeth blades placed in 10 pairs of 5 and 4ATB and FTG, and there are gaps between them to reduce the vibration. The gaps make it suitable for both crosscutting and ripping. The stabilizing gaps ensure that there is no disturbing vibration or wobble or tear out while working. 

Its multi-purpose versatility minimizes blade changes between tasks, which ultimately saves you time. However, you can’t expect it like the dedicated rip or crosscuts blades.

The thin, 0.98-inch kerf between the blade’s 50 ATB (alternate top bevel) teeth is laser cut for ease of feed to control the blade’s position. This ensures both the accuracy of the cut and the efficiency of your work.

The blade’s laser-cut stabilizer vents reduce noise and vibration during operation.

Freud’s exclusive shock-resistant TiCo Hi-Density Carbide formula helps fight wear and tear and maintains blade sharpness up to four times longer than ordinary carbide.

So, the Freud D1050X is a great addition to your workshop and is covered by Freud’s Limited Lifetime Warranty.

Pros

  • Fits Miter and Table Saws
  • Makes Clean, Razor-Sharp Cuts 
  • Produces Smooth, Quiet Cuts with Laser-Cut Kerf
  • Shock-Resistant Carbide for Long-Lasting Precision

Cons

  • Not like the dedicated ones

Buying Guide Of The Best Ripping Blade For Table Saw

Here is a buying guide for the best ripping blade where I am discussing the crucial considerations you need to make before purchasing one. 

Kerf

Kerf denotes the thickness of the blade that determines the width of the material removed while cutting. The higher the kerf, the more sawdust is in each cut. A standard full kerf blade is 1/8 inch thick. 

If the blade kerf is narrower than 1/8 inch, it’s called a thin kerf as they remove fewer materials on each cut. While thinner kerf is more prone to vibrations, thicker ones need more power to work. 

If your table saw is equipped with a 3 horsepower or more powerful motor, you can buy a full kerf blade. Thinner kerf blade suits the smaller saws or saws equipped with a lower-powered motor.

Blade Length

A smaller blade provides precise cuts, while a larger one requires more power to rotate and offer greater depth to cut through thicker boards. Small blades on equally powered saws revolve faster, resulting in smoother cuts. Most of the table saw come with a 10-inch blade. 

Remember, you can fit your table saw with a smaller blade but never try to fix a larger blade with a 10-inch table saw.

Blade Materials

You surely should check the blade material before purchasing one. Carbide size is crucial when it comes to sharpness and the rate at which an edge wears. The larger the carbide grain, the more an edge will wear. 

High-grade materials such as C-4 carbide may cost more but offer better durability. As you’ve already spent a lot on the table saw, don’t scrimp on the blade.

Additional Features

Many ripping blades are equipped with some additional features that improve their durability and performance.  

  • Anti-Vibration Vents

Anti-vibration slots prevent warping during use and reduce the noise produced from a vibrating blade. 

  • Blade Coatings

Lubricating coatings reduce friction and heat building up and allow faster cutting.

  • Anti-Kickback Shoulder

This feature helps to limit the speed of pushing a workpiece through a table saw by stopping too many materials from being removed at a time.

FAQs

Why are there burn marks on the cut edges?

The reason is the excessive heat from the saw blade scorches the stock as it goes through the wood. If the guide fence and saw blade are not perfectly aligned or the feed speed is incorrect, this can occur.

Why not are the ripping blades recommended for crosscuts?

The ripping blades generally tear out the fibers in terms of crosscutting.

Conclusion

So, which one is your Best Ripping Blade For Table Saw? Ripping blades are quite versatile.

You can use a ripping blade to cut a single piece of lumber in half or a separate portion or to cut through thick pieces of woods, or to make fast cuts for wood framing projects, and many more. Let me know what your next woodworking project is.

Happy DIY!